Crown XLS602D Power Amplifier
Crown's XLS Series of power amplifiers represents a new era in affordable, quality power amplification. Housed in a uniform, rugged 2U chassis, incorporating the best of tried-and-true design principles and innovative features. XLS Series amplifiers are professional stereo power amplifiers engineered to meet demanding audio requirements, reliably and within budget. Plus, every XLS Series amplifier is backed by Crowns unequaled Three-Year, No-Fault, Fully-Transferable Warranty that covers everything. With over five decades of experience designing and building rock-solid products, Crown is the standard in amp technology. Power Output Stereo: 380W @ 8 ohms; 600W @ 4 ohms; 840W @ 2 ohms Bridge-Mono: 1200W @ 8 ohms; 1680W @ 4 ohms Reliable design incorporates many popular featuresHoused in a rugged, all-steel 2U chassisEfficient forced-air fans prevent excessive thermal buildupElectronically balanced XLR inputs; touchproof binding post and Speakon® outputsPrecision detented level controls, power switch, power LED, and six LEDs which indicate signal, clip and fault for each channel.Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications Performance Sensitivity (volts RMS) for full rated power at 4 ohms: 1.25 V.Frequency Response (at 1 watt) 22 Hz to 20 kHz: +0 dB, –0.8 dB.Signal-to-Noise Ratio (20 Hz to 20 kHz) A-weighted, below rated power: >98 dB. No weighting, below rated power: >93 dB.Total Harmonic Distortion (THD): <0.5%.Intermodulation Distortion (IMD): (60 Hz and 7 kHz at 4:1) from full rated output to –40 dB: < 0.3%.Damping Factor (8 ohm) 10 Hz to 400 Hz: >200.Crosstalk (below rated power) at 1 kHz: –76 dB. at 20 kHz: –58 dB.Input Impedance (nominal): 20 kilohms balanced, 10 kilohms unbalanced.Load Impedance: Rated for 2 to 8 ohms per channel in Stereo, 4 to 8 ohms in Bridge Mono.AC Line Voltage and Frequency Configurations Available (±10%): 120 VAC 60 Hz, 100 VAC 50/60 Hz, 220 VAC 50 Hz, and 230-240 VAC Controls Level: Two front-panel rotary level controls, one for each channel.Power: Front-panel switch; on when in the IN position.Circuit Breaker: Back-panel breaker provides overload protection.Mode Switch: Back-panel switch selects Dual or Bridge-Mono mode. Indicators Signal Presence Indicators: Two green LEDs, one for each channel, illuminate when the channel’s input signal exceeds –40 dBu.Clip Indicators: Two red LEDs, one for each channel, illuminate when the channel’s output is being overdriven.Power Indicator: Blue LED indicates amplifier has been turned on and AC power is available.Fault Indicator: Two red LEDs illuminate when amplifier is in protect mode. Also illuminates briefly during normal power-up when amplifier is first switched on. Input/Output Input Connectors: One per channel; back-panel three-pin female XLR input connectors.Output Connectors: Two 4-Pole Speakon® Output Connectors accept 2-pole or 4-pole Speakon connectors. The top Speakon connector is wired for both channels so it can be used for bridge-mono wiring or for stereo wiring of two speakers to a single Speakon connector.One pair of back-panel binding posts per channel; accepts banana plugs or bare wire. (European models do not accept banana plugs.) Protection XLS Series amplifiers provide extensive protection and diagnostic capabilities, including output current limiting, DC protection, circuit breaker, and thermal protection. Construction Ventilation: Flow-through ventilation from front to back.Cooling: Internal heat sinks with forced-air cooling for rapid, uniform heat dissipation. Air Volume Requirements (per minute per unit): 80.15 ft³ (2.27 m³). Dimensions: EIA Standard 19-inch (48.3-cm) rack mount width (EIA RS-310-B), 3.5-inch (8.9-cm) height and 15.2-inch (38.6-cm) depth.
| Power Output (@ 8ohms) |
251 to 400 |
| Power Output (8/4/2 ohms/Bridged Mono) |
380/600/NA/1,200 @ 8 ohms |
| Audio Connections |
INPUTS: XLR / OUTPUTS: Touchproof Binding Posts & Speakon |
| Distortion |
< 0.5% - 20 Hz to 1k Hz |
| Indicators |
Power, Signal Presence, Clip, Fault LED's |
| Damping |
10 Hz to 400 Hz: >200 @ 8 ohms |
| Model |
XLS602D |
| Series |
XLS |
| Signal to Noise Ratio |
> 95 dB - No weighting, below rated power |
| Crosstalk |
–75 dB @ 1 kHz, –50 dB @ 20 kHz |
| Sensitivity |
1.25v @ 8 ohms |
| Dimensions |
19 x 15.2 x 3.5 |
| Product Weight |
29 |
| Voltage |
120 VAC 60 Hz, 100 VAC 50/60 Hz, 220 VAC 50 Hz, and 230-240 VAC |
| Fan |
Yes |
| Front Air Intake |
Yes |
| Rear Air Intake |
No |
| DSP |
No |
Crown XLS602D Power Amplifier
The manufacturer's warranty covers parts for three years and labor for three years from date of purchase. The warranty excludes damage from misuse, abuse, and contains other exclusions.
|
